![bmw inpa / ediabas k+dcan usb interface windows 10 bmw inpa / ediabas k+dcan usb interface windows 10](https://ae01.alicdn.com/kf/HTB1p5igKpXXXXa2XFXXq6xXFXXXe/FT232RL-Chip-INPA-Ediabas-K-DCAN-USB-Interface-For-bmw-OBD-CAN-Scan-Reader-Diagnostic-Cable.jpg)
- #BMW INPA / EDIABAS K+DCAN USB INTERFACE WINDOWS 10 HOW TO#
- #BMW INPA / EDIABAS K+DCAN USB INTERFACE WINDOWS 10 INSTALL#
- #BMW INPA / EDIABAS K+DCAN USB INTERFACE WINDOWS 10 UPDATE#
No one holds any responsibility of what you’ll try!į or sake of security, you can get tested versions: The link is only tested by a few users on the
![bmw inpa / ediabas k+dcan usb interface windows 10 bmw inpa / ediabas k+dcan usb interface windows 10](https://ae01.alicdn.com/kf/HTB1rMP8SXXXXXarapXXq6xXFXXXT/For-BMW-INPA-K-can-inpa-k-dcan-USB-OBD2-Interface-INPA-Ediabas-for-BMW-with.jpg)
#BMW INPA / EDIABAS K+DCAN USB INTERFACE WINDOWS 10 INSTALL#
PS:ISTA P is only for programming and coding ,not for diagnostic.I want to share Kpl BMW Standard tools and very easy way to install: just one click… Inpa support F01-F02–30 and all older Models also NCS-Expertentool with different Expertmode.įirst run Stansard tools 2.12 after install I hope you don't mind for this long thread, and also sorry for my English writing ,because I don't know better.
#BMW INPA / EDIABAS K+DCAN USB INTERFACE WINDOWS 10 UPDATE#
Or just update ecu with ,than select ecu family,enter VIN ,than and again. Īnd one more thing, for me WinKFP is also good solution for programming, because when you have new ZSUB numbers ,you just need to find that number in AIF thru INPA, and after that you just in WInKFP comfort mode ,put that number ,enter VIN ,than DONE and than again and everything is done! Yes I know it is crazy, but when it started, I must to finish everything.īMW ICOM is much better solution!īut for my car it was a problem for old ZSUB numbers which I did not managed to programĪll ecu-s thru WinKFP ,one by one.only few of them.Įverything about ecu-s in my bmw was from 2005 Īnyway I think there is no problem for programming 1 ecu with K DCAN usb, but keep in mind that voltage of the battery must be backup all the time and key must be on ignition position. I have done full car programming in about 12 hours!!! Ībout my experience, I must tell you that with K DCAN usb cable everything was fine but slow.įor my CCC Application programming time was about 8 hours!!!Įverything else was much faster, think I have 38 ecu programmed and coded thru ISTA P. but anyway, now I have a new version of ISTA P3.65.0.500 so you can go thru installation of 3.65.0.500 version. I don't remember thru that installation of ISTA P that I was needed some kind of activation key, only reg fix or something. I don't know for sure do you need to keep ISTA +,because I have installed Ista + before ISTA P version 3.65.0.500 which I have. Requirements for installation of ISTA P : min 200 gb free hdd,min 3-4gb RAM,and min 2ghz cpu speed,i hope you know. I can show you my programming and coding results few day before for my 5.with K DCAN usb. K+DCAN usb for 5 programming and coding results Now with BMW INPA K+CAN cable you can roll up the car windows via remote key!
![bmw inpa / ediabas k+dcan usb interface windows 10 bmw inpa / ediabas k+dcan usb interface windows 10](https://m.media-amazon.com/images/I/51VK1624cbL._AC_SX679_.jpg)
![bmw inpa / ediabas k+dcan usb interface windows 10 bmw inpa / ediabas k+dcan usb interface windows 10](http://sc04.alicdn.com/kf/Ha471df61e2d94f898f7e6f85553ca475O.jpg)
(Plug INPA cable into the USB port on your laptop, Windows XP system would be preferred, install INPA driver and then NCS Expert software)
#BMW INPA / EDIABAS K+DCAN USB INTERFACE WINDOWS 10 HOW TO#
Recommended Software: BMW INPA, EDIABAS and NCS EXPERT How to do BMW E series coding? (Set how to activate BMW remote windows up as example) Recommended Hardware: INPA K+CAN BMW cable (Only 15.99 USD)